Front Wheel Rotation Sensor Signal Inspection
The front wheel rotation sensor sends the signal to the ECU through the KIBS hydraulic unit (KIBS equipped models). For other than KIBS equipped models, the signal is sent directly to the ECU.
The ECU uses the wheel rotation sensor signal for KTRC control.
The service code 27 is detected with the ECU.
Service Code b 42 (see Front Wheel Rotation Sensor Signal Abnormal) Service Code b 43 (see Front Wheel Rotation Sensor Wiring Inspection)
Special Tool - Hand Tester: 57001-1394 Wiring Continuity Inspection ECU Connector [A] ← → KIBS ABS Hydraulic Unit Connector [B] G/Y lead (ECU terminal 4, KIBS Hydraulic Unit terminal 8) [C]
Wiring Continuity Inspection KIBS Hydraulic Unit Connector [A] ← → Front Wheel Rotation Sensor Connector [B] W lead (KIBS Hydraulic Unit Connector terminal 12) [C] Y lead (KIBS Hydraulic Unit Connector terminal 3) [D]
Special Tool - Hand Tester: 57001-1394 Wiring Continuity Inspection ECU Connector [A] ← → Front Wheel Rotation Sensor Connector [B] R lead (ECU terminal 58) [C] G/Y lead (ECU terminal 4) [D]
Front Resistor Resistance (in Main Harness) Connections: ECU Connector [A] ← → Ground [B] G/Y lead (ECU terminal 4) [C] Standard: 209 231 Ω
If the resistance is out of the standard, replace the main harness.
If the wiring is good, check the ECU for its ground and power supply (see ECU Power Supply Inspection in the Fuel System (DFI) chapter).
If the ground and power supply are good, replace the ECU (see ECU Removal/Installation in the Fuel System (DFI) chapter).
Wheel Rotation Sensor Circuit (KIBS Equipped Models)
1. ECU
2. Front Wheel Rotation Sensor
3. KIBS Hydraulic Unit
4. Rear Wheel Rotation Sensor
Wheel Rotation Sensor Circuit (other than KIBS Equipped Models)
1. ECU
2. Front Wheel Rotation Sensor
3. Resistor F 220 Ω
4. Resistor R 220 Ω
5. Frame Ground 3
6. Rear Wheel Rotation Sensor
This sensor has a weight [A] with two magnets inside,
and sends a signal to the ECU. But when the motorcycle
banks 60 70В° or more to either
side (in fact falls down),
the weight turns and the signal changes. The ECU senses
this change, and stops the fuel pump relay, the fuel injectors
and the ignition system.
Hall IC [B] When the motorcycle is down, the ignition switch is left ON. If the starter button is pushed, the electric starter turns but the engine does not start. To start the engine again, raise the motorcycle, turn the ignition switch to OFF, and then turn it to ON.
Vehicle-down Sensor [A] Ground Terminal [B]: BR/BK Output Terminal [C]: Y/G Input Terminal [D]: BL
Caliper Installation
Install the caliper and brake hose lower end.
For the front caliper, be sure to install the collars [A].
Replace the washers on each side of hose fitting with new
ones.
Touch the brake hoses [A] to the stopper [B] of the caliper.
Front Calipers [C]
Rear Caliper [D]
Tighten:
To ...
Fuel Pump Removal
WARNINGGasoline is extremely flammable and can be
explosive
under certain conditions, creating the
potential for serious burns. Make sure the area is
well-ventilated and free from any source of flame
or sparks; this includes any appliance with a pilot
light. Do not smoke. T ...
Kawasaki Intelligent anti-lock Brake System (KIBS,
For models equipped with KIBS)
KIBS regulates anti-lock braking performance
with more precision during
sports riding compared to a conventional
ABS system.
KIBS is designed to help prevent
the wheels from locking up when the
brakes are applied hard while riding
straight. KIBS automatically regulates
brake force using en ...