Kawasaki Ninja Service Manual: Master Cylinder Rubber Parts Replacement

Kawasaki Ninja Service Manual / Periodic Maintenance / Periodic Maintenance Procedures / Replacement Parts / Master Cylinder Rubber Parts Replacement

Front Master Cylinder Disassembly

Remove the front master cylinder (see Front Master Cylinder Removal in the Brakes chapter).
Remove the seal cover [A], circlip [B], connector [C] and O-ring [D].

Special Tool - Inside Circlip Pliers: 57001-143

Unscrew the locknut [E] and pivot bolt [F], and remove the brake lever.
Remove the bleed valve [G] and rubber cap [H].
Remove the piston assembly [I] as follows.

Remove the dust cover and push rod.

Remove the circlip [J]

Pull out the piston (with primary cup and secondary cup).

Remove the return spring and spring guide.

Master Cylinder Rubber Parts Replacement

Replace: Seal Cover [A] Circlip [B] O-ring [D] Rubber Cap [H] Piston Assembly [I] Circlip [J] Diaphragm [K]

Rear Master Cylinder Disassembly

Remove the rear master cylinder (see Rear Master Cylinder Removal in the Brakes chapter).
Remove the circlip [A], connector [B] and O-ring [C].

Special Tool - Inside Circlip Pliers: 57001-143

Rear Master Cylinder Disassembly

Slide the dust cover [D] out of place, and remove the circlip [E].
Pull out the push rod assembly [F].
Remove the piston assembly [G] and return spring.

Master Cylinder Assembly

Before assembly, clean all parts including the master cylinder with brake fluid or alcohol.

NOTICE

Except for the disc pads and disc, use only disc brake fluid, isopropyl alcohol, or ethyl alcohol for cleaning brake parts. Do not use any other fluid for cleaning these parts. Gasoline, engine oil, or any other petroleum distillate will cause deterioration of the rubber parts. Oil spilled on any part will be difficult to wash off completely, and will eventually deteriorate the rubber used in the disc brake.

Apply brake fluid to each parts and the inner wall of the cylinder.
When installing the piston assembly, take care not to scratch the piston or the inner wall of the cylinder.
Apply silicone grease to the followings.

Front: Brake Lever Pivot Bolt

Rear: Dust Cover of Push Rod Assembly

For the front master cylinder, tighten the brake lever pivot bolt and the locknut.

Torque - Brake Lever Pivot Bolt: 1.2 N·m (0.12 kgf·m, 11 in·lb) Brake Lever Pivot Bolt Locknut: 5.9 N·m (0.60 kgf·m, 52 in·lb)

For the front master cylinder, install the bleed valve and rubber cap.

Torque - Front Master Cylinder Bleed Valve: 5.4 N·m (0.55 kgf·m, 48 in·lb)

Fit the circlip into the groove of the cylinder securely.

Brake Fluid Change

NOTE The procedure to change the front brake fluid is as follows. Changing the rear brake fluid is the same as for the front brake. Level the brake fluid reservoir. Remove: Screw [A] ...

Caliper Rubber Parts Replacement

Front Caliper Disassembly Remove: Front Caliper (see Front Caliper Removal in the Brakes chapter) Brake Pads (see Front Brake Pad Removal in the Brakes chapter) Remove: Front Caliper A ...

Other materials:

Crankshaft Main Bearing Insert/Journal Wear Inspection
Split the crankcase (see Crankcase Splitting). Cut strips of plastigage to journal width. Place a strip on each journal parallel to the crankshaft installed in the correct position. Tighten the crankcase bolts to the specified torque (see Crankcase Assembly). NOTE Do not turn ...

Tightening Sequence
Generally, when installing a part with several bolts, nuts, or screws, start them all in their holes and tighten them to a snug fit. Then tighten them according to the specified sequence to prevent case warpage or deformation which can lead to malfunction. Conversely when loosening the bolts, n ...

Relay Box Removal
Remove the left fuel tank cover (see Fuel Tank Removal in the Fuel System (DFI) chapter). Disconnect the connectors [A]. Pull out the relay box [B] from the rubber protector [C]. NOTE The relay box has relays and diodes. The relays and diodes can not be removed. Relay Box Installa ...