Kawasaki Ninja Service Manual: Oxygen Sensor Heater Power Source Voltage Inspection

Kawasaki Ninja Service Manual / Self-Diagnosis System / Oxygen Sensor Heater (Service Code 67, Equipped Models) / Oxygen Sensor Heater Power Source Voltage Inspection

NOTE

Be sure the battery is fully charged.

Oxygen Sensor Heater Power Source Voltage Inspection

Turn the ignition switch to OFF.
Remove the fuel tank (see Fuel Tank Removal in the Fuel System (DFI) chapter).
Disconnect the oxygen sensor lead connector and connect the measuring adapter [A] between these connectors as shown in the figure.

Main Harness [B] Oxygen Sensor [C]

Special Tool - Measuring Adapter: 57001-1700

Connect a digitalmeter [D] to the measuring adapter lead.

Oxygen Sensor Heater Power Source Voltage Connections to Adapter: Digital Meter (+) → R (main harness W/R) lead Digital Meter (–) → Frame Ground terminal

Oxygen Sensor Heater Power Source Voltage Inspection

Measure the power source voltage with the engine stopped and with the connector joined.
Turn the ignition switch to ON.

Power Source Voltage Standard: Battery Voltage

Turn the ignition switch to OFF.

If the reading is in specification, but the problem still exists, replace the ECU (see ECU Removal/Installation in the Fuel System (DFI) chapter).

If the reading is out of the standard, check the following.

ECU Relay Fuse 15 A (see Fuse Inspection in the Electrical System chapter) Power Source Wiring (see Oxygen Sensor Circuit)

If the fuse and wiring are good, remove the ECU and check the wiring for continuity between harness connectors.

Special Tool - Hand Tester: 57001-1394

Disconnect the ECU and sensor connectors.

Oxygen Sensor Heater Power Source Voltage Inspection

Wiring Continuity Inspection ECU Connector [A] ←→ Oxygen Sensor Connectors [B] R lead (ECU terminal 76) [C]

If the wiring is good, check the ECU for its ground and power supply (see ECU Power Supply Inspection in the Fuel System (DFI) chapter).

If the ground and power supply are good, replace the ECU (see ECU Removal/Installation in the Fuel System (DFI) chapter).

Oxygen Sensor Circuit

Oxygen Sensor Circuit

1. ECU

2. Oxygen Sensor

3. Ignition Switch

4. Joint Connector F

5. Joint Connector A

6. Fuse Box 1

7. Ignition Fuse 15 A

8. Relay Box

9. ECU Main Relay

10. Frame Ground 3

11. Starter Relay

12. ECU Fuse 15 A

13. Main Fuse 30 A

14. Battery

15. Engine Ground

Oxygen Sensor Heater Resistance Inspection

Turn the ignition switch to OFF. Remove the fuel tank (see Fuel Tank Removal in the Fuel System (DFI) chapter). Disconnect the oxygen sensor lead connector [A]. Connect a digital me ...

KIBS Hydraulic Unit Communication Error (Service Code 1b, KIBS Equipped Models)

KIBS Hydraulic Unit Communication Line Inspection When the data (for status of KIBS hydraulic unit) is not sent from the KIBS hydraulic unit to the meter unit and ECU, the service code 1b is displa ...

Other materials:

Drive Chain Wear Inspection
Remove the chain cover (see Drive Chain Removal/Installation in the Final Drive chapter). Rotate the rear wheel to inspect the drive chain for damaged rollers, and loose pins and links If there is any irregularity, replace the drive chain. Lubricate the drive chain if it appears dry. ...

Check 3-5: Warning Indicator Light (Red LED) (Oil Pressure Warning) Inspection
Connect the leads in the same circuit as Check 3-2. Connect the terminal [10] to the battery (–) terminal. Check that the oil pressure warning symbol [A] and the warning indicator light (Red LED) [B] go on. If the indicator light does not go on, replace the meter unit. ...

Operating Procedures
Clean the seat area carefully. Coat the seat with machinist’s dye. Fit a 45° cutter into the holder and slide it into the valve guide. Press down lightly on the handle and turn it right or left. Grind the seating surface only until it is smooth. NOTICE Do not grind the seat too ...